Call for Availability
800.941.2446
A complete twin supercardioid microphone floor stand solution in the modular d:dicate™ Microphone Series offering a high-quality stage voice or instrument mic.
The floor stand has an elegant and exclusive design with a black, non-reflective surface specifically made to handle the, from time to time, rough life in TV-studios, OB-vans and onstage in theaters and concert halls. The Floor Base has an integrated shock mounting solution. The thread screw holds the Stand Extension and Active Boom Pole. This unique design allows for a long stage microphone boom pole that does not swing, but rapidly stabilizes itself after being positioned.
This floor stand solution comes in one length:
d:dicate™ 4018FGT Supercardioid Microphone, Single 122 cm (48 in) Boom, Floor Stand
The microphone capsule
The supercardioid shape is frequency independent, securing an identical sound color around the microphone. The usual rear lobe heard on most supercardioids is minimized on this capsule. This makes it much more isolated without sudden frequency dependent peaks and dips.
A truly flexible range
This mic is part of the flexible d:dicate™ Microphone Series. At any time, and with no tools needed, it is possible to transform the d:dicate™ 4018F Supercardioid Microphone into a new configuration. You can combine it with another d:dicate™ or d:facto™ Microphone Capsule or Preamplifier.
Features
The product offers the following features
Low noise and natural voice
Highly directional for high isolation
Most controlled supercardioid shape
Uniform, frequency independent directionality
Ultimate floor mic
Modular flexibility
d:dicate™ Recording Microphones 4018FGT SUPERCARDIOID MICROPHONE, TWIN 120 CM BOOM, FLOOR STAND
Directional pattern: Supercardioid
Principle of operation: Pressure gradient
Cartridge type: Pre-polarized condenser
Frequency range: 20 Hz - 20 kHz
Frequency range, ±2 dB, at 30 cm (11.8 in): 40 Hz - 18 kHz
Sensitivity, nominal, ±2 dB at 1 kHz: 12 mV/Pa; -38.4 dB re. 1 V/Pa
Equivalent noise level, A-weighted: Typ. 16 dB(A) re. 20 µPa (max. 19 dB(A))
Equivalent noise level, ITU-R BS.468-4: Typ. 23 dB
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 78 dB(A)
Total harmonic distortion (THD): < 1% up to 137 dB SPL peak
Dynamic range: Typ. 121 dB
Max. SPL, peak before clipping: 142 dB
Output impedance: 100 Ω
Minimum load impedance: 2 kΩ
Cable drive capability: 100 m (328 ft)
Output balance principle: Impedance balancing
Common mode rejection ratio (CMRR): > 40 dB
Power supply (for full performance): 48 V Phantom power (± 4 V)
Current consumption: 3.5 mA
Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Color: Matte black
Microphone diameter: 19 mm (0.75 in)
Capsule diameter: 19 mm (0.75 in)
Microphone length: Capsule: 23 mm (0.9 in), Boom pole: 122 cm (48 in)
Maximum output voltage, RMS: 2.2 V
Polarity: +V at pin 2 for positive sound pressure
Temperature range: -40°C to 45°C (-40°F to 113°F)
Relative humidity (RH): Up to 90%
Matching tolerance (frequency response and sensitivity): ±1 dB
Phase deviation for kit: < 10°